User Tools
servo-continuous-modify
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
servo-continuous-modify [2012/10/31 11:41] 194.29.25.78 |
servo-continuous-modify [2013/03/14 07:09] 62.50.2.178 rKjMRjOIQaJiFcEi |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Modify HiTEC servo HS-645MG for continuous rotation ====== | + | 28cgBa , [url=http://wfcxefkjuffv.com/]wfcxefkjuffv[/url], [link=http://emajyrgggwim.com/]emajyrgggwim[/link], http://shqibuubxrqq.com/ |
| - | + | ||
| - | + | ||
| - | HiTEC HS-645MG servo before modification | + | |
| - | + | ||
| - | {{::servo-modify-000.jpg?nolink&500|}} | + | |
| - | + | ||
| - | no soldering, no cutting, no part replacements..... | + | |
| - | + | ||
| - | !!! the modification is **reversible** (if you keep all the parts and don't damage anything, of course) | + | |
| - | + | ||
| - | ==== step 1: remove the screw which holds the arm ==== | + | |
| - | + | ||
| - | + | ||
| - | {{::servo-modify-001.jpg?nolink&500|}} | + | |
| - | + | ||
| - | ==== step 2: remove the arm ==== | + | |
| - | + | ||
| - | {{::servo-modify-002.jpg?nolink&500|}} | + | |
| - | + | ||
| - | ==== step 3: remove the 4 bottom screws ==== | + | |
| - | + | ||
| - | {{::servo-modify-003.jpg?nolink&500|}} | + | |
| - | + | ||
| - | ==== step 4: take the top and bottom part of the casing off ==== | + | |
| - | + | ||
| - | {{::servo-modify-004.jpg?nolink&500|}} | + | |
| - | + | ||
| - | ==== step 5: remove the screw which holds the potentiometer in place ==== | + | |
| - | + | ||
| - | {{::servo-modify-005.jpg?nolink&500|}} | + | |
| - | + | ||
| - | ==== step 6: remove the metal gear ==== | + | |
| - | + | ||
| - | * the gear with the pin will come off together with the second gear shown on the piece of paper. | + | |
| - | + | ||
| - | {{:servo-modify-006.jpg?nolink&500|}} | + | |
| - | + | ||
| - | ==== step 7: pull the potentiometer out ==== | + | |
| - | + | ||
| - | * it should come out very easily, no force needed | + | |
| - | + | ||
| - | {{::servo-modify-007.jpg?nolink&500|}} | + | |
| - | + | ||
| - | ==== step 8: make a hole in the casing ==== | + | |
| - | + | ||
| - | * the hole should be big enough for the three potentiometer wires to pass comfortably when you close back the casing. | + | |
| - | + | ||
| - | {{::servo-modify-008.jpg?nolink&500|}} | + | |
| - | + | ||
| - | ==== step 9: remove the metal pin from the gear ==== | + | |
| - | + | ||
| - | * hold the pin with a pair of locking pliers. gently hit the top of the gear with a hammer to push the pin out. be careful not to damage the gear. | + | |
| - | + | ||
| - | * you can save the pin, in case you want to modify the servo back to normal | + | |
| - | + | ||
| - | {{::servo-modify-009a.jpg?nolink&500|}} | + | |
| - | + | ||
| - | {{::servo-modify-009b.jpg?nolink&500|}} | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | + | ||
| - | + | ||
servo-continuous-modify.txt · Last modified: 2013/06/08 09:33 by zoza
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
