This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
rknfg [2015/04/28 12:59] zoza [software] |
rknfg [2015/04/28 15:24] zoza [hadrware] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== first prototype: RKNFG, salzamt, september 2012 ====== | + | ====== RKNFG, salzamt, september 2012 ====== |
Line 17: | Line 17: | ||
- plywood board base, 1x1m | - plywood board base, 1x1m | ||
- plywood board top, 1x1m | - plywood board top, 1x1m | ||
- | - white stretchable fabrix fixed on 3 sides | + | - white stretchable fabric (1.5x3m) fixed on 3 sides |
{{:img_20120906_152720.jpg?nolink&200|}} {{:img_20120907_231737.jpg?nolink&112|}} {{:img_20120909_212544.jpg?nolink&112|}} {{:img_20120909_212433.jpg?nolink&200|}} | {{:img_20120906_152720.jpg?nolink&200|}} {{:img_20120907_231737.jpg?nolink&112|}} {{:img_20120909_212544.jpg?nolink&112|}} {{:img_20120909_212433.jpg?nolink&200|}} | ||
Line 31: | Line 31: | ||
* [[http://www.aircrack-ng.org/|aircrack-ng]], scanning network traffic (looks up the traffic on a specific BSSID, writes a dump to a .csv file) | * [[http://www.aircrack-ng.org/|aircrack-ng]], scanning network traffic (looks up the traffic on a specific BSSID, writes a dump to a .csv file) | ||
- | * [[extended-python-arduino-api|extended-python-arduino API]] firmware for the Arduino, with the associated arduino library | + | * [[extended-python-arduino-api|extended-python-arduino API]] firmware for the Arduino, with the associated [[arduino-py|arduino library]] |
* python script [[motors-scanner-test-1|motor-scanner.py]]: reads the .csv file, calcutlates the next position of the linear actuators based on the difference in the number of packets since the last calculation | * python script [[motors-scanner-test-1|motor-scanner.py]]: reads the .csv file, calcutlates the next position of the linear actuators based on the difference in the number of packets since the last calculation | ||
Line 41: | Line 41: | ||
or | or | ||
* start aircrack scan | * start aircrack scan | ||
- | <code>/etc/init.d/networking stop # stop network manager | + | <code bash>/etc/init.d/networking stop # stop network manager |
killall wicd # if using wicd network manager for debian | killall wicd # if using wicd network manager for debian | ||
airmon-ng start wlan0 # start airmonitor on your wireless card; to check the name of the card run $ sudo ifconfig | airmon-ng start wlan0 # start airmonitor on your wireless card; to check the name of the card run $ sudo ifconfig | ||
Line 48: | Line 48: | ||
</code> | </code> | ||
* in a separate terminal, run the python script | * in a separate terminal, run the python script | ||
- | <code>python /path/to/your/folder/reading.py</code> | + | <code bash>python /path/to/your/folder/reading.py</code> |
* when finished, stop airmon-ng | * when finished, stop airmon-ng | ||
- | <code>airmon-ng stop wlan0 | + | <code bash>airmon-ng stop wlan0 |
airmon-ng stop mon0 | airmon-ng stop mon0 | ||
</code> | </code> | ||