emperor's new architecture research

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
Extended Python Arduino Prototyping API adruino pde [[http://code.google.com/p/extended-python-arduino-prototyping-api/source/browse/trunk/prototype/prototype.pde|google code]] project trunk

<code java>
#include <Servo.h>

int  VarSign = 1;
int  SerIn = -1;          // incoming byte from serial RX
long VarN[9] = {0, 0, 0, 0, 0, 0, 0, 0, 0};      // number array
int  PosN = -1;       // index counter
char VarHandlerChar = '@';

#define serv_size 4
Servo serv[serv_size];

int time_out_counter=0;
#define max_count_blinks 3
int count_blinks=0; // count blink then ready COM connection

// SERIAL PARSER 
void SerialParser(void) {
  while (Serial.available()) {
    SerIn = '@';
    SerIn = Serial.read();
    if ((SerIn >= 65) && (SerIn <= 90)) {          // if ASCII 'A' - 'Z'
      VarHandlerChar = SerIn;  
      for (PosN = 0; PosN < 9; PosN++) {           // clean up
        VarN[PosN] =  0;                           // reset Var array
      }  
      PosN = -1;                              
    }
    if (SerIn == 45) {
      VarSign = -1;
    }
    if ((SerIn >= 48) && (SerIn <= 57)) {          // if ASCII numeric '0' - '9'
      VarN[PosN] = VarN[PosN] * 10 + (SerIn - 48);
    }
    if (SerIn == ' ') {                            // if ASCII " " detected
      if (PosN > -1) {
        VarN[PosN] = VarSign * VarN[PosN];           // assign sign 
        VarSign = 1;
      }
      PosN++;
    }
    if (SerIn == 33 || SerIn == 10 || SerIn == 13) {  // '!' or CR or LF ends all this spooky things ...
      VarN[PosN] = VarSign * VarN[PosN];           // assign sign 
      VarSign = 1;
      CallHandler();                               // Call function by first Char
    }   
    time_out_counter=0; // reset time out
    count_blinks = 0;
  }
}

void ResetReadBuff(){
    VarHandlerChar='@';
    SerIn='@';
    VarSign=1;
    PosN=-1;
}

void CallHandler(void) {
  //DebugOut();
  switch(VarHandlerChar) {
  case 'D': // set digital D 1 2 1 ! - write pin 2 HIGH, D 0 2 ! - read pin 2
    DigitalHandler(VarN[0],VarN[1],VarN[2]);
    break;    
  case 'B':  // 
    DebugOut();
    break;
  case 'A':   // analogWrite
    AnalogHandler(VarN[0],VarN[1],VarN[2]);
    break;
  case 'S':  // servo control
    ServoHandler(VarN[0],VarN[1],VarN[2],VarN[3]);
    break;    
  case 'C': // configure pin
    ConfigurePinHandler(VarN[0],VarN[1]);
    break;
  case 'I': // init start state
    InitStateHandler();
    break;
  default:
    Serial.println('0');
  } // Switch END
}

void DebugOut(void) {
  Serial.print(VarHandlerChar);
  for (int  i = 0; i < PosN; i++) {
    Serial.print(' ');
    Serial.print(VarN[i]);
  }
  Serial.println(" !");
}

void InitStateHandler(){
    int i;
    for (i=0;i<serv_size;i++){
        if(serv[i].attached()){
            serv[i].detach();
        }
    }
    for (i=0;i<13; i++){
        pinMode(i,INPUT);
        digitalWrite(i,LOW);
    }
}

void ConfigurePinHandler(int pin_, int value_){
    if(value_<=0){
        pinMode(pin_,INPUT);
    }else{
        pinMode(pin_,OUTPUT);
    }
    Serial.println("0");
}

void DigitalHandler(int mode_, int pin_, int value_){
    if(mode_<=0){ //read
        Serial.println(digitalRead(pin_));
    }else{
        if(value_<=0){
            digitalWrite(pin_,LOW);
        }else{
            digitalWrite(pin_,HIGH);
        }
        Serial.println("0");
    }
}

void AnalogHandler(int mode_, int pin_, int value){
     if(mode_<=0){ //read
        Serial.println(analogRead(pin_));
    }else{
        analogWrite(pin_,value);
        Serial.println("0");
    }
}

void ServoHandler(int mode_, int number, int pin_, int value_){
    // Servo
    if(number>=serv_size){
        Serial.println("1");
        return;
    }
    switch(mode_){
    case 5: // attach()
      //add servo
      if(serv[number].attached()){
          serv[number].detach();
          serv[number].attach(pin_);
      }else{
          serv[number].attach(pin_);
      }
      Serial.println("0");
      break;
    case 6: // write()
      serv[number].write(value_);
      Serial.println("0");
      break;
    case 7: // read()
      Serial.println(serv[number].read());
      break;
    case 8: // attached()
      Serial.println(serv[number].attached());
      break;
    case 9: // dettach()
      if(serv[number].attached()){
        serv[number].detach();
      }
      Serial.println("0");
      break;
    }
}

void setup() {
  Serial.begin(9600);
  Serial.println(F_CPU);
}

void loop(){
    SerialParser();
    
    if ( time_out_counter>F_CPU/500){ // for response when time out call handler
        time_out_counter=0;
        Serial.println("0");
        ResetReadBuff();
        count_blinks++;
    }
    if(count_blinks < max_count_blinks){
        time_out_counter++;
    }
}

</code>
emperor's new architecture research

User Tools

Site Tools

Page Tools
